VEGAVIB S 61
 

　　Vibrating level switch for granulates
 

　　Easy setup without adjustment
 

　　Product-independent switching point
 

　　Optimum rod design avoids buildup and jamming
 

　　Easy cleaning
 

　　Wear and maintenance free
 

　　Function
 

　　The vibrating rod of VEGAVIB is energized by a piezo crystal and it vibrates at a fixed amplitude. If the vibrating rod is covered by product, the amplitude change is detected by the integral electronics and converted into a switch signal. The switching condition is visible from outside via a two colour LED. No special adjustments are required to set up VEGAVIB S 61.
 

　　Area of application
 

　　VEGAVIB S 61 is used as a level switch in free flowing powders, granulates and coarse grained solids and detects reliably and accuray when a point level is reached. The optimum rod design avoids jamming and buildup of bulk solid material. It is ideal as a high or low level switch in a vessel detecting foodstuffs, perishable or granulate materials,which could be retained in a fork solids level probe.
 

　　Technical data
 

Process pressure   -1…16 bar
 

　　Process temperature   -50…  +150℃
 

　　Density  ≥ 100 g/l
 

　　Material housing   plastic PBT
 

　　Protection    IP 66/IP 67
 

　　Materials, wetted parts   316L
 

　　Approval    option: ATEX II 1/3 D IP6X T
 

　　Electronics transistor (NPN/PNP)
 

　　Load current    max. 400 mA
 

　　Turn-on voltage   max. 55 V DC
 

　　Supply voltage    10…55 V DC
 

　　Power consumption   max. 0.5 W
 

　　Electronics double relay (DPDT)
 

　　Supply voltage    20…253 V AC, 50/60 Hz, 20…72 V DC
 

　　Power consumption   1…8 VA (AC), approx. 1.3 W (DC)
 

　　Turn-on voltage   min. 10 mV / max. 253 V AC/DC
 

　　Switching current   min. 10 μA / max. 3 A AC, 1 A DC
 

　　Breaking capacity   max. 750 VA, 54
 

　　Accessories:Sliding lock fitting (extended versions) pressurised or unpressurised for adjustable switch point
 

　　VEGAVIB S 61
 

　　振动极限开关，用于颗粒状的固料
 

　　安装方便, 无需调整
 

　　产品独立开关点
 

　　优化杆设计避免了堆积和干扰
 

　　易清洗
 

　　功能
 

　　VEGAVIB 的振动杆由压电晶体激发, 并以固定振幅振动。如果振动杆被产品覆盖, 则通过整体电子学检测振幅变化并转换成开关信号。开关情况从外面是可看见的通过LED指示灯显示。设置 VEGAVIB S 61 不需要进行特殊调整。
 

　　应用领域
 

　　VEGAVIB S 61 在自由流动的粉末、颗粒和粗粒固体中被用作电平开关, 并在达到点水平时进行可靠和准确的检测。*杆设计避免了大块固体材料的干扰和堆积。它是理想的作为一个高或低电平开关的船舶检测食品, 易腐或粒材料, 这可以保留在一个叉子固体水平探头。
 

　　技术资料
 

　　工艺压力-1..。16 bar
 

　　工艺温度-50... + 150℃
 

　　密度≥100克/升
 

　　材料外壳塑料 PBT
 

　　保护 ip 66/ip 67
 

　　材料, 湿部316L
 

批准选项: ATEX II 1/3 D IP6X T

电子晶体管 (NPN/PNP)

负载电流zui大值400 mA
 

　　开启电压zui大值55 V DC
 

　　电源电压 10…55 V DC
 

　　功耗zui大值0.5 W
 

　　电子双继电器 (双)
 

　　电源电压 20…253伏 AC, 50/60 赫兹, 20…72 V DC
 

　　功耗 1…8 VA (AC), 约 1.3 W (DC)
 

　　开启电压zui小10毫伏/zui大 253 V 交/直流
 

　　开关电流zui小 10 a/zui大值3 a AC, 1 DC
 

zui大破坏容量750 VA, 54 W

附件: 滑动锁配件 (扩展版) 加压或 unpressurised 可调开关点
 

　　以上即为VEGA VIB S61 6263的相关介绍，如有任何技术咨询或需要相关技术资料，请前往相关页面进行下载。